All ATF/NFA rules apply to purchases made from this site. The information/products in these web pages are not intended to be used to construct illegal firearms. It is the sole responsibility of the purchaser to know and understand all applicable Federal, State and local laws before placing an order. For legal semi auto and dummy gun information, contact BATF at:
www.atf.gov Every reasonable effort has been made to ensure that all photographs, descriptions and specifications on this website are accurate.
A registered business in the state of Colorado (ID# 20091276671 / 20131415285)
About Me / The Story Of HBA
Contact Us Here
Turn Around Times and Shipping
1910 Maxim Reproduction Parts
1910 Maxim Semi Conversion
1919 Internals Machining
Aurora Faux Suppressor
Build tools, Jigs and Helpful Items
CZ-23 / CZ-24 / CZ-25 / CZ-26
Carl Gustaf, Swedish K, Port Said, M/45
FBP (9mm) SMG
MP-34 Reciver / Bolt Services
MP-38 and MP-40
PPSH-41 Repair Sections and services
SLS (Semi-only) Sten Long Shroud Kits
Scratch, Dent and Ding Bin
Suomi M-31/ KP-31
VZ-58 Hybrid 80% (Non-FFL) Receivers
HBA Cause 4 K9s
Site Usage Tutorials
Commonly Asked Questions
Sales, When and Where?
HellBox Supported Pages
Forum Made By Home
Builders - For Home builders
80% Solutions & FFL work
Prexis / Precision American Rifles
For Home Builders
as well as 07 work
Denver Area FFL
Kits & Part Sources
HBA Recommends finishes from
1919 Internals Machining to Semi Only
Quantity in Basket:
Shipping Weight: 1.00 pounds
The right side of the bolt, barrel extension, and trigger frame require having a area milled out to allow them to fit past the simi-only island on a simi RSP (Right Side Plate).
In addition to this the simi only triggers have a disconnector built into them to allow them to disconnect from the sear, these require a clearance cut to be made in the accelerator (Located on the front of the trigger frame)
Lastly the sear slot has to be re-machined so that a F/A (Full Auto) sear can not be used - this entails widening the sear slot and re-cutting the internal retention slots so that a F/A sear can not be physically retained or function in the rear of the bolt.
If the Bolt, Lock and extension are sent intact (with all the associated parts) along with the semi internals to be used we can/will test fit them in one of our firearms to verify fit and function - we however will not strip pieces and parts from our firearms to fit onto your internals for testing. While this was done for a period and we found this can easily lead to parts becoming intermingled and or errantly shipped or errantly retained in the shop after shipping.
This service is done via CNC controlled equipment for optimum precision
This service is for the machining ONLY as no semi auto parts are provided/supplied by HBA, NFA items (Trigger and sear) will be discarded during the conversion unless it is specifically requested they be returned to the customer.
PLEASE NOTE! This service is for MACHINING ONLY. If you send us your internals caked and loaded with grease or cosmoline you will be charged a $25.00 cleaning fee (Or your parts will be machined and returned with the grease and cosmoline still intact along with any shavings that did not fall off following machining). Grease/Cosmoline deteriorates our machines coolant and creates difficulty in making sure the cuts are all good - Often this machining service consumes $65.00+ in tooling to do meaning a hours worth of time in cleaning of parts is simply not covered at this rate. Do us both a favor and clean/inspect your parts BEFORE they are mailed in.
By placing any order you are agreeing that you accept all legal responsibility for the products purchased and their subsequent use.
However, inadvertent errors may occur, and changes in design or materials, due to our continual effort to improve products, may result in some change in specifications before subsequent publications are issued.
HBA reserves the right to modify or change specifications with or without notice at any given time.
All ATF/NFA rules apply to purchases made from this site.
The information/products in these web pages are not intended to be used to construct illegal firearms.
It is the sole responsibility of the purchaser to know and understand all applicable Federal, State and local laws before placing an order.
For legal semi auto and dummy gun information, contact BATF at: www.atf.gov
Every reasonable effort has been made to ensure that all photographs, descriptions and specifications on this website are accurate.